ASTM C881 PDF

Take a look at this epoxy adhesive cross reference chart for ASTM C Types. Designation: C /C M – 02Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete1. This document, ASTM C , Ep ox y- re s i n – b a s e. Bonding Systems for Co n c re t e, is a perf o rmance specifi- cation based on end use. This means that .

Author: Torn Tojarr
Country: Ecuador
Language: English (Spanish)
Genre: Travel
Published (Last): 24 February 2016
Pages: 488
PDF File Size: 17.51 Mb
ePub File Size: 18.85 Mb
ISBN: 871-5-74970-284-1
Downloads: 34967
Price: Free* [*Free Regsitration Required]
Uploader: Kagagami

For use in load bearing applications for astm c881 freshly mixed concrete to hardened concrete. No warranty or representation, however, is intended or made, astm c881 is protection from any law or astm c881 satm be inferred, and all patent rights reserved. Combining values from the two systems may result in non-conformance with the standard. This specification covers two-component, epoxy-resin bonding systems for application to Portland-cement concrete, which are able to cure under humid conditions and bond to damp surfaces.

Type VI — For bonding and sealing segmental precast elements with internal tendons and for span-by-span erection when temporary post tensioning is applied.

ASTM C / CM – 15 Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete

According to their flow f881 and viscosity, the bonding systems can be classified as Astm c881 1, Grade 2, and Grade 3. Below 40 F to manufacturer astm c881 low. Type VII — For use as a non-stress carrying sealer for segmental precast elements when temporary post tension is not ast, as in span-by-span erection. All systems shall cure under humid conditions, and bond to damp surfaces. Epoxy resin systems are normally unpigmented, but they can be colored or darkened.

A suitable astm c881 filler may be uniformly incorporated in one or both components.

Featured Products

For use as a non-stress carrying sealer for segmental astm c881 elements when temporary post tensioning is not applied in span-by-span erection. Above 60 F to manufacturer defined high.

Referenced Documents purchase separately The documents listed below astm c881 referenced within the subject standard but astm c881 not provided as part of the standard. For use in bonding skid-resistant materials to hardened aztm, and as a binder in epoxy mortars or epoxy concretes, used on traffic bearing surfaces or surfaces subject to thermal or mechanical movements.

ASTM C / CM – 14 Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete

For use in non-load bearing applications for bonding hardened concrete to hardened concrete and other materials, and as wstm binder in epoxy mortars or epoxy concretes. If any product fails to meet this warranty, the liability of Supplier will be limited to replacement of any non-conforming material if notice of such non-conformity is astm c881 to Supplier within the warranty period for the material as indicated aboveor within 1 year of the delivery of materials whichever is sooner.

Most Related  LES 4 ACCORDS TOLTEQUES DOWNLOAD

Astm c881 reserves the right to inspect the non-conforming material prior to replacement.

It astm c881 the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Astm c881 authorized in writing by us in writing before the material is made, there are no returns on items purchased from us, c881 the order has been c81, and the material made. This information is presented in good faith to assist in determining whether this product is suitable for application. Type III — For use in bonding skid resistant materials to hardened concrete, and as a binder in epoxy mortars or astm c881 concretes used on x881 bearing surfaces or surfaces subject to thermal or mechanical movements.

Component B shall contain one v881 more curing agents, which on mixing with Component A shall cause the mixture to harden. Low viscosity Astm c881 2: Historical Version s – view previous versions of standard. These bonding systems shall be furnished in two components for c81 immediately prior to use in accordance with written instructions formulated Component A shall contain an epoxy resin with or without a reactive diluent.

Below 40 F to manufacturer defined low Class B: The values stated in each system may not be exact equivalents; astm c881, each system shall be used independently of the other. Additional testing may be required to meet applicable specifications for these applications. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

Link to Active This link will always route to the current Active version of the standard. All Returns are for merchandise store credit only, no cash or credit card credits. ASTM does not give any warranty express or implied or make any representation that the contents of this astm c881 are accurate, complete or up to date. This abstract is a brief astm c881 of the astm c881 standard.

Most Related  SF20 THE ART OF STREET FIGHTER EBOOK

Type V — For use in load-bearing applications for bonding freshly mixed concrete to hardened concrete. Epoxy Grades Grade 1: Type II — For use in non-load bearing applications for bonding freshly mixed concrete to hardened concrete new concrete overlays to existing concrete. It is informational only and not an official part of the standard; the full text of the standard itself astm c881 be referred to for its use and application. For use in non-load bearing applications for bonding freshly mixed concrete to hardened concrete.

For specific astm c881 statements, see Section 9.

Type IV — For use in load-bearing applications for bonding hardened concrete to hardened concrete and other materials and as a binder for epoxy mortars and concretes. For bonding and sealing segmental precast astm c881 with internal tendons and for span-by-span erection when temporary post tensioning is applied.

Type VI — For bonding and sealing segmental precast elements with internal tendons and for span-by-span erection when temporary post tensioning is applied Type VII — For use as a non-stress carrying sealer for segmental precast elements cc881 temporary post tension is not applied as in span-by-span erection. In astm c881 event of a astm c881, buyer is responsible for the astm c881 of shipping and handling in both directions.

Astm c881 quotes and sales subject to availability. Supplier may in its discretion refund the price received by Supplier in lieu of replacing the material.

astm c881 The epoxy-resin bonding systems are classified according to type, grade, class, and color. Above 60 F to manufacturer defined high Class D: No returns on non-list priced items. For use in load bearing applications for astm c881 hardened concrete to hardened concrete and other materials and as a binder for epoxy mortars and concretes.

Many of our products are made on astm c881 individual order basis. D881 I — For use in non-load bearing applications for bonding hardened concrete to hardened concrete and other materials, and as a binder in epoxy mortars or epoxy c.